Install The Control Panel Install the control panel onto the column as shown in the following Diagram: Screw M6x20 Electric control assembly Fit the electric control to the column using the supplied screws as shown in the adjacent diagram. Check the nameplate to ensure that the motor is suitable for the voltage available at the customer’s premises. Establish the electrical connections as shown in the circuit diagram (point 6.2). Use the cables and lines supplied for this purpose. Work must be carried out in accordance with local regulations. Make sure that the phases are properly connected (direction of rotation) and the lift is properly grounded. ® Copyright ATH-Heinl GmbH & Co. KG, All rights reserved / Misprints and technical changes reserved / As of: 2021-09 Manufacturer ATH-Heinl GmbH & CO.KG - 23 -
2.10 Completion of Work Before commissioning, check all fastening screws, electrical, pneumatic and hydraulic lines and, if necessary, tighten these. Warning: in some cases, this must be checked at regular intervals and tightened if necessary (note in the instructions). Adjustment of the top end-limit switch Limit switch Raise the lift at a height of 1870 mm to check for the proper position. If the switch does not function properly, unloosen its lever and adjust it at a proper position until the lift can reach at the desired height. Tighten the screw after adjustment. Adjustment of the CE-limit switch Place the lift at a height of 200 mm Limit switch Cross beam If the switch does not function properly, unloosen its lever and adjust it at a proper height (it is suggested to be lower 1-3mm than the cross beam). Tighten the screw after adjustment. ® Copyright ATH-Heinl GmbH & Co. KG, All rights reserved / Misprints and technical changes reserved / As of: 2021-09 Manufacturer ATH-Heinl GmbH & CO.KG - 24 -
Deutsch English Polskie Français
Inhalt 1.0 EINLEITUNG .............
1.2 Beschreibung Abdeckung oben Um
1.3 Bedienung Taster Heben um Hebeb
Sicherheitshinweise 1. Achten Sie a
Traglastverteilung Q Gesamtgewicht
® Urheberrecht ATH-Heinl GmbH & CO
2.3 Lieferumfang Transportbox mit:
2.5 Befestigung Hierbei sind die al
2.9 Montage Diese Anleitung ist nic
Installation des Netzteils Setzen S
Anschluss der Hydraulikleitung Acht
Raccordement de la ligne hydrauliqu
2.10 Travaux finaux Avant la mise e
Vérifier le bon fonctionnement de
3.0 EXPLOITATION 3.1 Manuel d'utili
4.0 MAINTENANCE Afin de garantir le
4.3 Remarques Quel que soit l'état
Problèmes lors de l'abaissement Le
4.7 Élimination • Coupez l'alime
6.0 ANNEXE 6.1 Schéma pneumatique
6.3 Schéma hydraulique 1 Filtre à
7.1 Étendue de la garantie produit
8.1 Procès-verbal d'installation e
8.3 Contrôle visuel (personne qual
Contrôle visuel (personne qualifi
9.0 NOTICES ® Droit d'auteur ATH-H
www.ath-heinl.de ATH-Heinl GmbH & C
Spis treści 1.0 WPROWADZENIE .....
1.2 Opis Pokrywa na górze Aby zakr
1.3 Obsługa Przycisk podnoszenia p
Instrukcje bezpieczeństwa 1. Zwró
Rozkład obciążenia Q Całkowita
® Prawa autorskie ATH-Heinl GmbH &
2.3 Zakres dostawy Skrzynia transpo
2.5 Mocowanie W tym przypadku nale
2.9 Montaż Niniejszej instrukcji n
Instalacja zasilacza Umieść zasil
Podłączenie linii hydraulicznej U
2.10 Prace końcowe Przed uruchomie
Sprawdź, czy wyłącznik krańcowy
3.0 PRACA 3.1 Instrukcja eksploatac
4.0 KONSERWACJA Aby zapewnić bezpi
4.3 Wskazówki Bez względu na zani
Problemy z opuszczaniem Winda sama
4.7 Utylizacja • Odłączyć dop
6.0 ZAŁĄCZNIK 6.1 Schemat obwodu
6.3 Schemat obwodu hydraulicznego 1
7.1 Zakres gwarancji produktu • P
8.1 Protokół ustawiania i przekaz
8.3 Kontrola wzrokowa (upoważniona
Kontrola wzrokowa (upoważniona oso
9.0 NOTIZEN ® Prawa autorskie ATH-
www.ath-heinl.de ATH-Heinl GmbH & C
Laden...
Laden...
Laden...
LinkedIn
Facebook
Instagram
Youtube
Email
Twitter
Pinterest