Minimum requirement: PROMAT chemicals special compressed air oil Item No.: 4000355209 Cleaning Minimum requirement: Caramba intensive brake cleaner acetone-free Care and protection of metals, painted or powder-coated surfaces Minimum requirement: Petec spray translucent - 500 ml Item No. 73550 Petec wall inlet translucent - 1000 ml Item No. 73510 Petec UBS pistol Item No. 98507 Care and protection of metals, painted or powder-coated surfaces in the tread area and plastic parts Minimum requirement: Valet Pro Classic Protectant Plastic Sealant 500 ml 4.2 Safety Regulations for Oil Always observe the legal requirements or regulations for handling used oil. Always dispose of used oil through a certified organisation. In the case of leaks, oil must be collected immediately with binders or trays so that it cannot penetrate into the soil. Avoid any skin contact with the oil. Do not allow oil vapours to escape into the atmosphere. Oil is a combustible medium. Pay attention to possible hazards. Wear oil-resistant protective clothing, such as gloves, goggles, protective clothing, etc. ® Copyright ATH-Heinl GmbH & Co. KG, All rights reserved / Misprints and technical changes reserved / As of: 2020-03 Manufacturer ATH-Heinl GmbH & CO.KG - 30 -
4.3 Notes Regardless of the level of dirt, the machine must be maintained, cleaned and serviced at regular intervals. The machine should then be treated with a care product (such as oil or wax spray). Do not use cleaning agents that are harmful to the skin. IF THE ABOVEMENTIONED POINTS ARE NOT FULFILLED, THE WARRANTY CLAIM IS EXCLUDED 4.4 Maintenance or Service Plan Interval Immediately Weekly Monthly Every 3 months Every 6 months Check of ALL safety-relevant parts Cleaning Check or restore surface protection Check for leaks in the hydraulic system Check or restore surface protection or corrosion protection Check or restore damage to the paint and components Check or restore rust damage Check or treat cavities and non-painted areas Check for leaks in the pneumatic system Control the tightness of screws Check, lubricate & adjust bearing slack Check wear parts Check fluids (level, wear, contamination, quality) Check and lubricate sliding surfaces Remove any dirt inside Clean and check electrical components Check motor and transmission for function and wear Check welds and construction Visual inspection (according to inspection plan) X X X X X X X X X X X X X X X X X X X ® Copyright ATH-Heinl GmbH & Co. KG, All rights reserved / Misprints and technical changes reserved / As of: 2020-03 Manufacturer ATH-Heinl GmbH & CO.KG - 31 -
BEDIENUNGSANLEITUNG / OPERATING INS
BEDIENUNGSANLEITUNG ATH Four Lift 5
1.0 EINLEITUNG 1.1 Allgemeine Infor
1. Hubsäulen In den Hubsäulen wer
Sicherheitshinweise GEFAHRENHINWEIS
Traglastverteilung Typ ATH-Four Lif
2.0 INSTALLATION Die Maschine muss
3. 4x Säulenabdeckungen Länge Bre
Zeichnung B1 Abstand Hauptsäule -
2.8 Hydraulischer Anschluss Bevor d
Montage Aufstellen und Ausrichten d
Führen Sie nun die Fangstangen (Ra
- Kontrollieren Sie die Diagonalen
2.10 Abschlussarbeiten Prüfen Sie
3.0 BETRIEB 3.1 Betriebsanweisung F
4.0 WARTUNG Um einen sicheren Betri
4.0 MAINTENANCE Afin de garantir le
4.3 Remarques Quel que soit l'état
Problèmes lors de l'abaissement Le
4.7 Élimination Coupez l'alime
6.0 ANNEXE 6.1 Schéma pneumatique
6.3 Schéma hydraulique 1 Moteur et
7.1 Étendue de la garantie produit
8.1 Procès-verbal d'installation e
8.3 Contrôle visuel (personne qual
Contrôle visuel (personne qualifi
9.0 NOTICES ® Droit d'auteur ATH-H
® Droit d'auteur ATH-Heinl GmbH &
NÁVOD K OBSLUZE ATH Four Lift 55_5
1.0 ÚVOD 1.1 Obecné informace TEN
1. Zdvižné sloupy Ve zvedacích s
Bezpečnostní upozornění BEZPEČ
Rozložení nosnosti Typ ATH-Four L
2.0 INSTALACE Stroj musí v souladu
3. 4x kryty sloupů Délka Šířka
Výkres B1 d1 Vzdálenost hlavní s
2.8 Hydraulické připojení Před
Montáž Instalace a vyrovnání ra
Nyní veďte zachycovací tyče (z
- Zkontrolujte úhlopříčky (viz
2.10 Závěrečné práce Nastaven
3.0 PROVOZ 3.1 Provozní pokyn Firm
4.0 ÚDRŽBA Za účelem zajištěn
4.3 Upozornění Na stroji je nezby
Problémy při spouštění Zkontro
4.7 Likvidace Odstraňte přív
6.0 PŘÍLOHA 6.1 Schéma pneumatic
6.3 Schéma hydraulického zapojen
7.1 Rozsah záruky na výrobek P
8.1 Protokol o umístění a před
8.3 Vizuální kontrola (povolanou
Vizuální kontrola (povolanou odbo
9.0 POZNÁMKY ® Copyright ATH-Hein
® Copyright ATH-Heinl GmbH & CO.KG
MANUAL DE INSTRUCCIONES ATH Four Li
1.0 INTRODUCCIÓN 1.1 Información
1. Columnas de elevación En las co
Indicaciones de seguridad INFORMACI
Distribución de la carga Tipo ATH-
2.0 INSTALACIÓN La instalación de
3. 4x tapas de columna Largo Ancho
Ilustración B1 L1 Distancia column
2.8 Conexión hidráulica Antes de
Montaje Montaje y alineación de la
Ahora pase las barras de intercepci
- Presione el botón ASCENDER, desp
2.10 Trabajos finales Antes de la p
3.0 FUNCIONAMIENTO 3.1 Manual de fu
4.0 MANTENIMIENTO Para garantizar u
4.3 Avisos Independientemente del g
Problemas durante el descenso Los e
4.7 Eliminación Retire la alim
6.0 ANEXO 6.1 Esquema de conexiones
6.3 Esquema de conexiones hidráuli
7.1 Alcance de la garantía del pro
8.1 Protocolo de instalación y tra
8.3 Inspección visual (especialist
Inspección visual (especialista au
9.0 NOTAS ® Copyright ATH-Heinl Gm
® Copyright ATH-Heinl GmbH & CO.KG
BEDIENINGSHANDLEIDING ATH Four Lift
1.0 INLEIDING 1.1 Algemene informat
1. Hefkolommen In de hefkolommen wo
Veiligheidsinstructies GEVARENAANDU
Draaglastverdeling Type ATH-Four Li
2.0 INSTALLEREN De machine mag uits
3. 4x kolomafdekkingen Lengte Breed
Tekening B1 Afstand hoofdkolom - wa
2.8 Hydraulische aansluiting Voorda
Montage Opbouwen en uitlijnen van d
Steek nu de vangstangen (grendelsch
- Druk op de knop HEFFEN, na korte
2.10 Afsluitende werkzaamheden Cont
3.0 GEBRUIK 3.1 Gebruikersinstructi
4.0 ONDERHOUD Om de machine veilig
4.3 Aanwijzingen De machine moet, o
Problemen bij neerlaten. Beveiligin
4.7 Afvoeren Ontkoppel de persl
6.0 BIJLAGE 6.1 Pneumatisch schakel
6.3 Hydraulisch schakelschema 1 Mot
7.1 Omvang van de productgarantie
8.1 Opstellings- en overdrachtsrapp
8.3 Visuele inspectie (door geautor
Visuele inspectie (door geautorisee
9.0 NOTITIES ® copyright ATH-Heinl
® copyright ATH-Heinl GmbH & Co. K
INSTRUKCJA OBŁSUGI ATH Four Lift 5
1.0 WPROWADZENIE 1.1 Informacje og
1. Kolumny podnoszące W kolumnach
Wskazówki bezpieczeństwa WSKAZÓW
Rozdzielenie podnoszonego ciężaru
2.0 INSTALACJA Maszyna musi być za
3. 4x pokrywa kolumn Długość Sze
Rysunek B1 L1 Odstęp kolumna głó
2.8 Przyłącze hydrauliczne Przed
Montaż Ustawianie i instalacja ram
Następnie poprowadzić pręty zabe
- Nacisnąć przycisk PODNOSZENIE,
2.10 Prace końcowe Przed uruchomie
3.0 PRACA 3.1 Instrukcja eksploatac
4.0 KONSERWACJA Aby zapewnić bezpi
4.3 Wskazówki Bez względu na zani
Problemy podczas opuszczania Zapadk
4.7 Utylizacja Odłączyć dop
6.0 ZAŁĄCZNIK 6.1 Schemat obwodu
6.3 Schemat obwodu hydraulicznego 1
7.1 Zakres gwarancji produktu Pi
8.1 Protokół ustawiania i przekaz
8.3 Kontrola wzrokowa (upoważniona
Kontrola wzrokowa (upoważniona oso
9.0 NOTATKI ® Prawa autorskie ATH-
® Prawa autorskie ATH-Heinl GmbH &
NÁVOD NA OBSLUHU ATH Four Lift 55_
1.0 ÚVOD 1.1 Všeobecné informác
1. Zdvižné stĺpy V zdvižných s
Bezpečnostné upozornenia UPOZORNE
Rozloženie nosnej záťaže Typ AT
2.0 INŠTALÁCIA Stroj musí v súl
3. 4 x kryty stĺpov Dĺžka Šírk
Výkres B1 L1 Vzdialenosť Hlavný
2.8 Hydraulické pripojenie Pred uv
Montáž Postavenie a vyrovnanie r
Veďte teraz zachytávacie tyče (d
- Následne sa stĺpy voči priečn
2.10 Záverečné práce Pred uvede
3.0 PREVÁDZKA 3.1 Prevádzkový po
4.0 ÚDRŽBA Na účely zaistenia b
4.3 Upozornenia Na stroji je nutné
Problémy pri poklese Bezpečnostn
4.7 Likvidácia Odstráňte pr
6.0 PRÍLOHA 6.1 Schéma pneumatick
6.3 Schéma hydraulického zapojeni
7.1 Rozsah záruky na výrobok P
8.1 Protokol o umiestnení a odovzd
8.3 Zraková kontrola (povolanou od
Zraková kontrola (povolanou odborn
9.0 POZNÁMKY ® Copyright ATH-Hein
® Copyright ATH-Heinl GmbH & CO.KG
Laden...
Laden...
Laden...
LinkedIn
Facebook
Instagram
Youtube
Email
Twitter
Pinterest