Aufrufe
vor 3 Jahren

ATH-Heinl Bedienungsanleitung ATH-Lux 3D

  • Text
  • Bedienungsanleitung

WARNING Do not stack

WARNING Do not stack other goods on top of the packaging to avoid damaging it. Handling To move the packing, insert the forklift tines into the slots in the base of the packaging itself (pallet). To move the machine, use the trim wheels; to lift it, insert the forklift tines under the lower platform of the wheeled cabinet, keeping it near the trim wheels. plus the maximum allowed load, including the supporting base to the ground and the specific securing devices. Install the aligner at the desired work position; make sure there is at least 25 cm between the rear part of the machine and the nearest wall. IMPORTANT: for the correct and safe machine operation, the lighting level in the place of use should be at least 300 lux. WARNING The machine must not be operated in a potentially explosive atmosphere. CAUTION Always use suitable hoisting belts or tested ropes. WARNING This operation must be carried out very carefully to prevent the unit from tipping over or being damaged. CAUTION Handle with care: violent vibrations may damage the equipment. CAUTION Keep the original packaging materials so that the machine can be safely shipped at a later date if necessary. WARNING Before moving the equipment, first unplug the power supply cable from its socket. CAUTION If the machine is to be installed outdoors, it must be properly sheltered under a roof or any other protection device to avoid contact with water. CAUTION Make sure there are no permanent magnets, electromagnets or heat sources near the machine (this might irreparably damage the program disk and the Personal Computer). WARNING Take the utmost care when unpacking, assembling, lifting and setting up the machine as described in this heading. Failure to observe these recommendations may result in damage to the machine and may jeopardise the operator's safety. Installation INSTALLATION AND SET-UP Installation clearances WARNING All regulations in force concerning safety at work must be complied with when choosing the installation position. The ground must be sturdy enough to bear a weight equal to the sum of the equipment weight WARNING Carry out the unpacking, assembly, lifting and installation operations described with care. Failure to comply with these instructions could damage the machine and put the operator at risk. Assembling the equipment - Unpack the equipment, placing the packaging in the position shown by the markings on it. - Unpack the personal computer. - Remove the monitor from its packaging. ® Urheberrecht ATH-Heinl GmbH & Co KG, Alle Rechte vorbehalten / Druckfehler und technische Änderungen vorbehalten Stand: 2022-01, Produkthersteller ATH-Heinl GmbH & Co KG 5

- Assemble the column (7, Fig 1), consisting of 2 parts. - Install the shelf (2, fig.1). - Install the PC Box (4, fig.1) and insert the PC. - Remove the rear panel of the column. - Connect the USB hub (HUB, Figure 2) to a free USB port on the back of the PC. - Install keyboard, mouse and printer by connecting to the USB HUB (HUB, fig.2). - Install the monitor stand to the monitor and mount them on the column (1, Figure 1), using the provided screws. -Connect the printer to the main supply via the power strip located inside the bottom of the column. -Connect the monitor to the PC and the power supply, through the power strip located inside the bottom of the column. - Mount the beam (6, Figure 1) using the provided screws. - Connect the camera movement control cable (CM, Fig. 2) to the Camera Movement main electric box. From the lower opening of the Beam out of 4 USB type cables and 1 power type. Bring 4 USB cables inside the PC Box through the rear hole (L1-C1-L2-C2, Fig. 2). - Connect the 2 camera USB cable with 2 USB ports on the back of the PC (C1-C2, Figure 2). - Connect the 2 USB cables with molded ferrite (Light indications cards) to the USB HUB (L1-L2, Figure 2). - Connect the Beam power cord to +12 V switching power supply output (PS, Figure 2), paying attention to the polarity (BROWN wire = +12 V, BLUE wire = GROUND). - Connect the switching power supply to the power supply (PS, Fig. 2). - Connect the PC to the mains supply (Fig. 2) via the strip placed inside the lower part of the column. - Connect the cables with the aid of the wiring diagram (Fig. 40); all the plugs are clearly indicated on their respective PC sockets. Push the plugs in completely without straining and, where applicable, tighten the lock screws. - The aligner wheel is factory-set to operate with a mains voltage of 230Vac. The wheel aligner may be configured to operate with a mains voltage of 115Vac. - Refit the rear panel of the column, fastening with the specific tool provided. - Connect the power supply cable to the plug provided; first read the “Electrical Hook-up” section. - Turn on the aligner with the main switch and the monitor and the printer with the specific switches. - Update the wheel aligner software if necessary, “Updating the Wheel Aligner Software” section, and install any optional kits, “Installing Additional Functions” section. Software protection key installation Insert the software protection key supplied in a free USB port of the USB HUB (SP, Figure 2). The software protection key is required to use the aligner. CAUTION For additional information about the technical characteristics, warnings, maintenance and any other data about the monitor or the printer, read the relative operator’s manuals supplied with machine documentation. Upgrading the wheel aligner software The wheel aligner is supplied with the software already installed, and is complete with an installation CD-ROM. After installing the wheel aligner, switch on the machine and go to the starting screen. Press the key combination È + F12 (upper case + F12): the software version will appear on the top left of the screen, beneath the logo. Compare the software release (indicated as “SW STD …”) with that stated on the installation CD-ROM supplied with the aligner. If the CD-ROM release is more recent than the release installed, update the aligner software. Detailed information about the software update procedure is provided in the leaflet accompanying the CD-ROM. AMBIENT CONDITIONS IN THE PLACE OF OPERATION • Relative humidity: 20% ÷ 90% (without condensation) • Temperature range: 0°C ÷ 35°C WARNING The machine must not be operated in a potentially explosive atmosphere. ® Urheberrecht ATH-Heinl GmbH & Co KG, Alle Rechte vorbehalten / Druckfehler und technische Änderungen vorbehalten / 6 Stand: 2022-01, Produkthersteller ATH-Heinl GmbH & Co KG

ATH-Heinl GmbH & Co. KG Gewerbepark 9 92278 Illschwang Deutschland
Tel.: +49 (0) 9666 18801-00 Fax: +49 (0) 9666 18801-01 Web: www.ath-heinl.de Impressum: ATH-Heinl GmbH & Co. KG